The "Super OCD" has a few extra controls:
- Firstly the "Bass" control - it's nicked from Paul C's Timmy pedal and works very well to add in pregain bass for more low end response.
- Secondly the "Saturation" control, this allows you to increase the clipping headroom of the circuit and have an overall "cleaner" tone while dialling in just the required amount of diode clipping.
- Thirdly the "Boost" control, I've configured the second opamp to allow a range of clean boosts to be selected to really allow you to push the front end of your amp into overdrive.
- The final control I've added is a switch to go between 9 volt and 18 volt operation. The 18 volt operation adds extra headroom to the circuit to stop the opamp clipping from fogging up the tone. The 9 volt operation retains the original headroom seen in the OCD.
- Other changes include alterations to the Tone control and a swap of opamp from the TL082 in the original OCD to the Burr Brown OPA2134. These changes all add up to create a really nice overdrive/distortion box. It's got all the original Fulltone OCD tones in there and loads more. If you like the original OCD you'll love the Super OCD.
- Firstly the "Bass" control - it's nicked from Paul C's Timmy pedal and works very well to add in pregain bass for more low end response.
- Secondly the "Saturation" control, this allows you to increase the clipping headroom of the circuit and have an overall "cleaner" tone while dialling in just the required amount of diode clipping.
- Thirdly the "Boost" control, I've configured the second opamp to allow a range of clean boosts to be selected to really allow you to push the front end of your amp into overdrive.
- The final control I've added is a switch to go between 9 volt and 18 volt operation. The 18 volt operation adds extra headroom to the circuit to stop the opamp clipping from fogging up the tone. The 9 volt operation retains the original headroom seen in the OCD.
- Other changes include alterations to the Tone control and a swap of opamp from the TL082 in the original OCD to the Burr Brown OPA2134. These changes all add up to create a really nice overdrive/distortion box. It's got all the original Fulltone OCD tones in there and loads more. If you like the original OCD you'll love the Super OCD.
I've laid this out for board mounted pots (from the solder-side with right angle PCB pots) and it should fit in a 1590B. (Though when I build this thing, it's definitely going in a 125B haha)
EDIT: Forgot to include what Q1-2 are–like in the original OCD, use 2N7000 MOSFETs.
woooooooooow!
ReplyDeleteHai, thanks for this great layout. I had built and working well. I'm curious, has anyone compare it with the original fulltone OCD? I watched youtube demo and it seems not so much gain as I found my build is very high gain. Before build super OCD, I also built OCD v3 on veroboard and very high gain.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeletefar better then the version 4 ocd
DeleteThis comment has been removed by the author.
ReplyDeleteDid anyone experiment with the variable values? the 10-15k resistor and 22-68nf cap?
ReplyDeleteits really dark so if i were you i would use 10k,22nf and lower the 100pf caps as well
DeleteYou're right this thing is dark, I went with the 22nf but I think I still have a 12k where the 10k should be. I had to put a buffer in front of it to stop it squealing too.
Deleteanyone have a drill template? Please and thank you!
ReplyDeleteCan the boost be engage/disengage using a 3pdt/dpdt footswitch?
ReplyDeleteNot easily with this layout. The Boost pot is essentially another gain control but in the 2nd op amp.
DeleteEazy-peazy. All you need is an SPDT across the outer pins of the boost pot. When the switch is closed, the pot is bypassed = minimum gain from the second opamp. Opening the switch un-bypasses the pot.
DeleteDark sound? Mistake with tone pot.Look at the schem OCD, and do the same! & you Will high tones!
ReplyDeletewich pot is it?
Deletecan anybody help me? I set up the right circuit but when I turn on the speaker "keeps shouting like a whistle and cuts the signal, which may be happening
ReplyDeleteThis comment has been removed by the author.
DeleteSounds like high pitched sound when not playing? Could be charge pump. Be sure to use MAX1044SCPA, not CPA. You Can also try TC1044SCPA or ICL7660SCPA. Cheers!
DeleteThis comment has been removed by the author.
ReplyDeleteAnyone have the schematic for this that's not the hand drawn one? Struggling to read it...
ReplyDeleteNeed an schematic to add the voltage switch without the other 3 pots
ReplyDelete