This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.
the image of q2 is wrong, mirrored, I imagine that if you used an image of 2N transistors, and forgot to change the image. The letters are correct, but the transistor is inverted on the board.
Hi, thanks for your comment, I was looking for possible problems with the pedal, since I was putting it all day, it was a whole day lost ... but I said, this can not be, it will not overcome this situation. so I started looking for information, to check with the oscilloscope, and found nothing, I said, will be the transistor? , I took it, I measured it and it was good, I changed it for another and nothing ... I changed the IC and nothing ... now that I read your comment, I'll put the plate back together ... since I ended up throwing it thinking that it was bad, I hope it is what you say about the transistor, I have reviewed the datasheet and it is as you say, therefore the transistor should be inverted :) thanks regards I leave here the transistor datasheet, greetings, thanks :)
Hello, thanks for your answer. So you said it's good for slapback, but for longer delay settings it isn't so good? Is there any sound sample i could hear? Thanks again!
There's a short demo of it at the end of the perf tutorial video on my YouTube channel (link at the top of the page). Longer delay times it gets pretty lofi.
No YouTube tem vídeo, ele funciona bem, já montei algumas vezes e acabei fazendo algumas modificações. Eh um projeto interessante pra quem tá começando a mexer com delay já que precisa de poucos componentes. Monta numa protoboard pra vc experimentar.
the transistor 78l05 is the same that 7805?
ReplyDeleteYep, same thing.
DeleteIs Bc549b replacable?
ReplyDeleteSocket and use what you have on hand. I used a BC550C and it worked fine. 2N5088/89 should also work.
Deletethe image of q2 is wrong, mirrored, I imagine that if you used an image of 2N transistors, and forgot to change the image. The letters are correct, but the transistor is inverted on the board.
ReplyDeleteTHanks dude !!! from chile
DeleteCz. :)
Hi, thanks for your comment, I was looking for possible problems with the pedal, since I was putting it all day, it was a whole day lost ... but I said, this can not be, it will not overcome this situation. so I started looking for information, to check with the oscilloscope, and found nothing, I said, will be the transistor? , I took it, I measured it and it was good, I changed it for another and nothing ... I changed the IC and nothing ... now that I read your comment, I'll put the plate back together ... since I ended up throwing it thinking that it was bad, I hope it is what you say about the transistor, I have reviewed the datasheet and it is as you say, therefore the transistor should be inverted :) thanks regards
ReplyDeleteI leave here the transistor datasheet, greetings, thanks :)
So, does this pedal work? I want to build it for its simplicity. Do you recommend this build?
ReplyDeleteI built it and it works fine. It's good for slapback settings and good starter if you haven't built a PT2399 delay before.
DeleteHello, thanks for your answer. So you said it's good for slapback, but for longer delay settings it isn't so good? Is there any sound sample i could hear? Thanks again!
DeleteThere's a short demo of it at the end of the perf tutorial video on my YouTube channel (link at the top of the page). Longer delay times it gets pretty lofi.
Deletethe diagram is correct :), personally to me, pot 100k repeat high position is coupled, the same as the pedal blue delay
DeleteThis comment has been removed by the author.
ReplyDeleteeste funciona legal ?????.... outros projetos não tive sucesso .... esse tem vídeo?
ReplyDeleteNo YouTube tem vídeo, ele funciona bem, já montei algumas vezes e acabei fazendo algumas modificações. Eh um projeto interessante pra quem tá começando a mexer com delay já que precisa de poucos componentes. Monta numa protoboard pra vc experimentar.
Deletetem o link ??
Deletenao achei
pessoal fiz funcionou blz mas quando coloco efeito abaixo som
ReplyDeleteHi, i made it using just 2N5089 in Q2 but i have a quite big volume loss. Is there something i can change to bring it back to unity? thanks
ReplyDelete