This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Tuesday, August 28, 2018

Mr. Black BB-74x

This is Jack Deville's Marshall-in-a-box emulating a 1974X 18-watt combo amp. Tracing credit goes to Ralf Gottschalk, who has a nice little dual-layer board of this up on OshPark if you don't feel like etching or grabbing the perf for this one (build doc with schematic in the description).




27 comments:

  1. Nice layout, thanks.

    Unfortunately, op amp pedals can't truly emulate amp-related distortion. I hope boutique pedal builders will realize it someday amd all this hoax will die.

    ReplyDelete
    Replies
    1. I love the simplicity of op amps. But I agree, fETs are the best simulation.

      Delete
  2. Hi, greetings from indonesia
    I have finished on perf board. It's works.
    Thanks for great layout..

    Sorry for my english.

    ReplyDelete
    Replies
    1. Thanks for verifying! How does it compare to demos?

      Delete
  3. After test my build and compare with the demo, i think my build have more loud volume. I roll up master pots about 9 it's realy loud. And if i roll up tone pots in max i get weird sound like high freq noise.
    I don't have 51k resistor. So i replace with 39k and 12k in series because i think its have more space for 2 resistor in series. It's ok?

    ReplyDelete
  4. You can replace the 51k resistors with any other value (10-100k), but both must be the same value. It's only a voltage divider.

    ReplyDelete
  5. This comment has been removed by the author.

    ReplyDelete
  6. Hi! Maybe I'm wrong but I think there is a little mistake with this layout. Both sides of the 100R/1N4148 pairs connect to the pin 1 of the 4558 instead of across the feedback, so as drawn it would work as a booster instead of an overdrive. What do you think?

    ReplyDelete
    Replies
    1. I belive you are right. From the schematic, both the 100R in series with the clipping diodes should go to pin 2 of the 4885. That also explains why Fuji's build is louder than the demo.

      Delete
    2. You are right. You'd just ned to swap the placement of the 100Ω resistors and the 4148 diodes to correct it. I'll update the layout momentarily.

      Delete
    3. Hi from Brazil! Have you corrected the layout above? It looks the same with both sides of the 100R/1N4148 pairs connected to the pin 1 of the 4558 instead of across the feedback as Zen of Tone mentioned before. Maybe I missed something. Could you please explain the corrected version? Thanks!

      Delete
    4. Oh man. Just all kinds of brain farts on my end. I miss read what Zen said and thought I had the 100Ω resistors connected to pin 1 instead of pin 2. NOW it's fixed and I'm going to bed. lol

      Delete
    5. Great! Everything looks good now! All the best, ZoT.

      Delete
  7. This comment has been removed by the author.

    ReplyDelete
  8. No worries.. Thanks a lot, mate!

    ReplyDelete
  9. This comment has been removed by the author.

    ReplyDelete
  10. Hey, I see you used my demo! That’s pretty cool. I hope everyone enjoys it!

    ReplyDelete
  11. What do you suggest for the non polarized 1uf caps?

    ReplyDelete
    Replies
    1. The grey film box caps from Tayda are what what it's laid out for, but other can be used.

      Delete
  12. once again a great layout, tested and had a great sound, thank you very much for your work here on the site, without you it would be very difficult to have access to such accurate information, greetings from Brazil

    ReplyDelete
  13. Replies
    1. It's in the Dropbox folder with the rest of them:

      https://www.dropbox.com/s/zfg1s7guo9x66j3/Mr%20Black%20BB-74x%20drilling%20template.pdf?dl=0

      Delete
    2. Thanks David! This pedal worths an enclosure!

      Delete
  14. This comment has been removed by the author.

    ReplyDelete
    Replies
    1. Sorry my mistake. It works. Thanks for the layout.

      Delete