This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Tuesday, August 18, 2015

Paul Cochrane's Timmy

Often cloned without giving credit to where credit is due (cough*lovepedal*cough), the Timmy is one of the most sought after overdrives on the market today. And really, if you can afford one, just buy one from Paul C. He's a great guy. For those of you who can't, here's my layout.



35 comments:

  1. Hi there,I'am not a noob guy in building guitar pedals,but it's a firs time I see component,named DIP 1,2.Can you please explain me what is this,I'm going to verify this one.
    Best regards,Daniel

    ReplyDelete
    Replies
    1. That's just a switch to engage D5 and/or D6. More info here:
      https://en.wikipedia.org/wiki/DIP_switch

      You could use a DPDT toggle instead. Wire the 2 pads for the DIP switch that connect to Drive 3 to lugs 2 and 4 (refer to the General Layout Notes page for lug numbering), and the pads that go to D5 and 6 to lugs 1 and 3. I think there are versions from Paul C. that are wired this way. Hope that helps!

      Delete
    2. Do you have one photo of this kind of DIP,12 ?

      Delete
    3. Is this it ?

      https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcTum0UB1k20Fbt_grXnJj_zJutdmIXP2Xo3occKGkIOGzkyXq5F

      Delete
  2. I'm mid-build on this one and don't see the output. Is it volume 2 to out?

    ReplyDelete
  3. Thanks. I hope to verify this one in the next couple of days.

    ReplyDelete
  4. Verified !! ... great pedal. Rock n roll.

    ReplyDelete
  5. I just boxed this timmy. Thanks for the layout.

    ReplyDelete
  6. https://www.instagram.com/p/BFzqCcQpsBi/?taken-by=lightsoundgeometry&hl=en

    getting ready to test mine tonight, so far so good

    ReplyDelete
    Replies
    1. got it!!! was a loose ground connection and now it sounds awesome. holy chit mane !

      Delete
  7. JRC4559 would be ok for this one?

    ReplyDelete
    Replies
    1. Yep. That's what's used in the original. I used a 4558 when I built this though. Worked fine.

      Delete
  8. How could one wire a 3 way switch to perform the clipping tasks of the later versions? Thanks for so many great layouts btw!

    ReplyDelete
    Replies
    1. Thanks! Check out the diode switching in lvlark's vero layout.

      http://4.bp.blogspot.com/-X-FXRN3YBpk/T32Ps68_v4I/AAAAAAAABL4/WvCN-7Vx3Mk/s1600/Paul+Cochrane+Timmy.png

      Delete
  9. The scheme of the Lovepedal OD11 is almost a copy of this pedal, know you if I can use the same board? Maybe I have to ask less and try more... jaja

    ReplyDelete
    Replies
    1. Explore the site a bit more. There are actually 2 layouts for the Lovepedal version.

      Delete
  10. Hi !
    sorry but can't find the layout in the data base … Could you please tell me where is the folder ?

    ReplyDelete
  11. I dont have a 510k resistor,would 470k sub ok?

    ReplyDelete
  12. can i use this op Amp? = LM1458CN

    ReplyDelete
  13. i bought a Pot says 50K,but i measured it in actual, value is only 37K,can i still use it?

    ReplyDelete
    Replies
    1. Pots can have pretty high tolerances. It's probably fine.

      Delete
  14. Hi Effects Layouts, i used LM1458CN Op Amp and the 37Kohm (actual measured Pot),and used your PCB layout.and tested sounds great transparent Overdrive,Thanks to Paul C. and to you Effects layout..this is VERIFIED!

    ReplyDelete
  15. This comment has been removed by the author.

    ReplyDelete
  16. About the d5 and d6 on the pad per hole layout..a connection is missing :)

    ReplyDelete
  17. Built this the gain pot is not working.and also the switch for the diode.i cant hear any difference(i used toggle dpdt switch and used only 4 poles) please advice 😢

    ReplyDelete
    Replies
    1. Still waiting for advice after a year has passed 😅😅😅

      Delete
    2. Post pics of your build, it helps a lot.Maybe is a bad solder joint somewhere

      Delete
  18. Is there a way to wire the dipswitch slots in a way that I don't need to use a dipswitch and the pedal stays in the equivalent of the middle position toggle of the version 3.

    Another question, If I want to reemplace the dipswitch with a 3 position toggle, how i have to wire ir in this board?

    ReplyDelete
  19. Excellent low gain drive pedal, just the right guitar frequenties!
    One problem i experienced was the Treble and Bass work way better with 50KC (anti-log) pots.
    Nice layout work!

    ReplyDelete