This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Tuesday, November 7, 2017

Earthquaker Devices Palisades

The mother of all TS808 derivatives/variants, the Palisades incorporates just about every mod to the classic Tube Screamer circuit. Two rotary switches control the bass response (Bandwidth) and clipping (Voice), one toggle bypasses the input buffer while the other is a bright switch, a footswitch selects between 2 separate gain pots, and with an added boost section to round it all off. All 5 pots are board mounted, but there will still be a good bit of off board wiring. Schematic can be found over on FSB. It's laid out for a 1790NS enclosure just like the original.



And because I'm sure the off board wiring isn't the clearest, here's a full wiring diagram:


Hopefully that clarifies any questions and doesn't raise more... haha!
at
Labels: , ,

14 comments:

  1. UnknownNovember 7, 2017 at 11:47 AM

    Awesome job as usual !

    ReplyDelete
  2. ernestoNovember 8, 2017 at 7:27 PM

    this is crazy man, Thanks for sharing

    ReplyDelete
  3. PeteJanuary 5, 2018 at 3:16 PM

    I finally got around to this one. It sounds great. Lots of tones to experiment with. Verified!

    ReplyDelete
  4. UnknownJanuary 13, 2018 at 3:42 AM

    This comment has been removed by the author.

    ReplyDelete
  5. UnknownAugust 26, 2018 at 3:51 PM

    Is there anything special about the 1uF caps? Just curious why they're large/grey.

    ReplyDelete
    Replies
    1. Effects LayoutsAugust 26, 2018 at 4:13 PM

      They're just non-polarized box caps like the ones from Tayda. You can use whatever.

      Delete
  6. MassimilianoDecember 26, 2018 at 4:51 PM

    This comment has been removed by the author.

    ReplyDelete
  7. MAtixApril 8, 2019 at 4:56 AM

    Hey, i have trouble with this pedal. 1. when i use the boost, my signal goes quietly, 2. on my voice, i have only 3 positions and ond the Bandwidth hasent any function. maybe someone can help me

    ReplyDelete
  8. SlackJuly 24, 2019 at 1:40 PM

    This comment has been removed by the author.

    ReplyDelete
    Replies
    1. SlackJuly 24, 2019 at 1:44 PM

      This comment has been removed by the author.

      Delete
    2. SlackJune 25, 2020 at 7:30 PM

      This comment has been removed by the author.

      Delete
  9. VLTRAJuly 2, 2021 at 4:24 AM

    Hi! Just checking this circuit to compare power section in another diagram with this' and I'm wondering why 100R resistor (+9V input) in diagram is linked in parallel to 100uf cap and 4001 diode, but in series in the board before those 2 components. Thanks in advance, I've built a lot of this site's circuits and layouts and I'm learning a lot and enjoying my pedals! \m/

    ReplyDelete
  10. UnknownJuly 19, 2021 at 7:15 PM

    buenas alguien tubo algun plop en el switchs de gain? tengo un plog cuando seteo cliping de led y clippins de menos recortes

    ReplyDelete

Subscribe to: Post Comments (Atom)