This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Monday, May 23, 2016

Ibanez TS808 Tube Screamer - 1590A

I've had a couple requests for a 1590A friendly Tube Screamer, and lately I've really been enjoying laying out 1590A boards, so here it is. Since there's 3 potentiometers, you'll need to use 9mm pots, and the 3PDT footswitch is board mounted. I would suggest using small profile jacks for this like these, or just measure really carefully when drilling the enclosure. Note that the 100uF power filter capacitor is folded on it's side for space purposes.

at
Labels: , , ,

50 comments:

  1. UnknownMay 23, 2016 at 9:12 AM

    You're a HERO!!!

    ReplyDelete
  2. Cormac O'DwyerMay 23, 2016 at 10:11 AM

    I'm liking the board-mounted footswitch idea!

    ReplyDelete
  3. UnknownMay 23, 2016 at 4:20 PM

    This is verified \m/

    ReplyDelete
  4. UnknownMay 23, 2016 at 5:10 PM

    Not a fan of the TS but woah what a cool compact layout!

    ReplyDelete
  5. Joe TafanoMay 24, 2016 at 5:31 AM

    Great. Thank you
    Another great layout
    Thank you
    joe

    ReplyDelete
  6. UnknownMay 24, 2016 at 6:04 AM

    Storyboardist for a president

    ReplyDelete
  7. UnknownMay 24, 2016 at 7:32 AM

    How are you mounting the 3PDT? Because it would be hard to solder it on the under side of the board. Are you reverse mounting the PCB like in Boss pedals? Cool layout either way :)))

    ReplyDelete
    Replies
    1. Effects LayoutsMay 24, 2016 at 7:47 AM

      Everything gets mounted on the top side of the board.

      Delete
    2. UnknownMay 25, 2016 at 6:25 AM

      Rad. I thought so. Sorry I was just gettin' my head around it.

      Delete
  8. BerkicauMay 24, 2016 at 8:15 AM

    Mad Professor Royal Blue overdrive pls...!
    sorry...

    ReplyDelete
  9. Joe TafanoMay 24, 2016 at 8:18 AM

    Please Himmelstrutz fetto in a 1590A if possible. It would be great!!!
    joe

    ReplyDelete
  10. urbanknight.ruJuly 3, 2016 at 5:32 PM

    Why capacitor 100uf square and has no holes on the board?

    ReplyDelete
    Replies
    1. BerkicauJuly 4, 2016 at 9:32 AM

      the cap is folded to fit this into the enclosure
      the holes are: + pole at the red track, - pole at the end of the green one, all of em above the 1n2001 diode

      Delete
    2. urbanknight.ruJuly 4, 2016 at 11:45 AM

      But I can make holes in the board and bend the leg at a right angle. Yes?

      Delete
    3. BerkicauJuly 4, 2016 at 6:07 PM

      yes, you are actually HAVE TO make holes to solder the cap to the board; and yes, you can bend it to any direction you like, as long as you connect the pin in the correct position.

      Delete
    4. MAtixFebruary 25, 2019 at 5:05 PM

      Hey, this is my first build and i have a question. Is the 100 uf capacitor or special capacitor? Or is it a normal electrolytic capacitor. Im a bit confused of " power filter capacitor"

      Delete
    5. Effects LayoutsFebruary 25, 2019 at 5:37 PM

      It's a normal polarized electrolytic cap. It's function is to filter the power, but any 100uF electrolytic will work there as long as its voltage rating is high enough. (I generally go with 35v)

      Delete
    6. MAtixFebruary 25, 2019 at 6:07 PM

      Thx man!!!

      Delete
  11. Göktürk SeyhanOctober 15, 2016 at 5:10 AM

    If you short the 47 nf cap, you can get a fat bass distortion and try LEDs for softer clipping. I use it this way with harmonica.

    ReplyDelete
  12. UnknownNovember 24, 2016 at 11:33 AM

    Is the resistor 1/8 or 1/4? Thanks

    ReplyDelete
  13. UnknownNovember 25, 2016 at 1:47 PM

    Okay...BTW is there any list of these components?
    Thanks again and mabuhay from Philippines...

    ReplyDelete
  14. UnknownDecember 15, 2016 at 4:25 PM

    Is the gain pot being used with only two terminals? Do I just cut off either the 2nd or the 3rd one?

    ReplyDelete
  15. AnonymousApril 26, 2017 at 4:15 AM

    i etched the big muff nad tube screamer but botched driling and mounting 3pdts...is there a way to cut off board mounted 3pdt section and wire directly to board....i see how for everything but lugs 3, 6 and 9

    ReplyDelete
    Replies
    1. Effects LayoutsApril 26, 2017 at 10:47 AM

      I guess you could just cut of the part of the board with the footswitch. Lugs 3 and 6 jumper together, and lug 9 you can either connect to lug 4 (this grounds the effect when it's bypassed) or just leave it unconnected.

      Delete
  16. AnonymousApril 26, 2017 at 4:16 AM

    i mean wire as in use wires, im gonna order some 3pdts with pins on next order then there wont be an issuse

    ReplyDelete
  17. UnknownMay 23, 2017 at 11:14 AM

    is the 1uf cap`s tantal? can you show the polarity?

    ReplyDelete
  18. Who Am IJuly 12, 2017 at 1:46 PM

    Potensio B for Linear or Logaritmis? Cause different for some region. And for the input use the mono jack or stereo? Thanks before ^_^

    ReplyDelete
    Replies
    1. Effects LayoutsJuly 13, 2017 at 9:43 PM

      B = linear. If you're putting this in a 1590A, you'll probably not be using a battery, so no need for a stereo input jack.

      Delete
  19. CharonAugust 27, 2017 at 7:19 PM

    Just finished mine. A few words of advice to others:

    In at least the smallbear 1590a enclosure, you are going to need to mount those skinny jacks as close to the top of the enclosure as you can, else it won't fit. Closer than the drilling template suggests. By 5-6mm.

    Don't install the electrolytic caps until you verify fitment in the enclosure. You might need to leave the leads long so you can lay it over a few mm further away than the layout suggests. Or order some super-compact caps -- they exist.

    Remember to buy a PC mount stomp switch if you are using the pads for the switch.

    ReplyDelete
  20. ElRuso82December 21, 2017 at 12:08 PM

    led color?

    ReplyDelete
  21. MAtixMarch 6, 2019 at 11:47 AM

    This comment has been removed by the author.

    ReplyDelete
  22. MAtixMarch 6, 2019 at 11:49 AM

    I have a question about the 51pf ceramic capacitor. I cant find one with this value in our local shops or in our online shops. Can i replace it with 47 pf or 56 pf? Or is it problematic?

    ReplyDelete
  23. Max PietriniApril 1, 2019 at 4:00 PM

    Verified. Fantastic sound!

    ReplyDelete
  24. MetalheadJuly 2, 2019 at 8:52 AM

    Sounds good, thanks

    ReplyDelete
  25. AnonymousOctober 17, 2019 at 10:57 PM

    Dude, thank you so much. It was jolly good fun to etch and to populate. Sounds brilliant too. I stock with the 20K tone pot, I have 25K pots at hand, but they are large. I thank you again, you're truly a legend.

    ReplyDelete
  26. Subekhic69@gmail.comSeptember 17, 2020 at 7:06 PM

    Kalau switchnya pakai DPDT kaki 6 pengaruh suaranya nggak

    ReplyDelete
  27. jadenacMarch 7, 2021 at 11:40 AM

    I know im stretching a bit here, but by any chance does anyone has this in cad or gerber?

    ReplyDelete
  28. UnknownDecember 10, 2021 at 2:31 AM

    Hello, where can I find the diagram?

    ReplyDelete
  29. StefanoJanuary 11, 2022 at 12:56 PM

    Hi it's possible to replace the 51pf capacitor with a 56pf?
    Thank's

    ReplyDelete

Subscribe to: Post Comments (Atom)