This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Thursday, November 30, 2017

Rothwell Love Squeeze

Here's a nice little compressor that should be a fairly easy build. It doesn't have the squish of a DynaComp, but goes for a more subtle compression like the Orange Squeezer. Board mounted pots and an easy fit in a 1590B. Here's the schematic for reference.


30 comments:

  1. OMG I was just watching how it is compared to 4knob keeley. This wins it!! AWESOME!
    surely build it

    ReplyDelete
  2. are you sure that 10uF below the volume oriented correctly? just wondering

    ReplyDelete
    Replies
    1. That's how it is in the schematic and a verified stripboard layout I referenced. So yes.

      Delete
  3. Very good, I was waiting for a layout of this pedal ... Thanks

    ReplyDelete
  4. AHA, finally. A good perf Lovesqueeze layout
    Can 5819 replace 5817?
    and is good replace 10u with MLCC?

    ReplyDelete
    Replies
    1. Don't know for sure, but probably.

      Delete
    2. I'm thinking the same, 5819 for 5817. how's the result?

      Delete
  5. hi,

    I cant seem to find the transfer image...

    ReplyDelete
  6. Not build yet... but double check with schematic everyday, looks like everything is fine, but dont know the effect about replace scothky diode,.. must to try it

    ReplyDelete
  7. Interesting conversation about the diodes of this compressor:

    http://www.diystompboxes.com/smfforum/index.php?topic=100976.msg890136#msg890136

    Both BAR43S and BAT43 have the same forward voltage (already checked), so you can use the latter. I would use sockets and try BAT43 and 5817

    ReplyDelete
  8. You can mark this one as verified. I just finished the build - it sounds great!

    ReplyDelete
    Replies
    1. Did u get pop sound while playing muted notes?

      Delete
  9. I build this using 2n5458 to replace 2n5457, and a pair 1n5817 to replace 5819. It works, but when I turn up the comp pot, the sound gets louder and bassier. any clue?

    ReplyDelete
  10. Built one, but it sounds weird. The compression is not really subtle in my build, the signal is being 'pumped' way too hard (especially when playing soft on lower strings) on every position of comp pot. Used 5817 diodes and 2n5457 transistor.

    ReplyDelete
  11. Ciao, ho Sentito il video e suona benissimo, COMPLIMENTI!! VOLEVO CHIEDERTI SE c'è il disegno elettrico. Devo farlo subito perché è bellissimo!!

    ReplyDelete
  12. Q bc5457,,,,OR BS170,,,or,,bc549 is good? Provisional. Grazie, sei bravissimo. Saluti dall'Italia.

    ReplyDelete
    Replies
    1. It needs to be a JFET like a 5457. The BS170 is a MOSFET, and the BC549 is a BJT.

      Delete
  13. Hello!

    I made 2 of these. I didnt have any 2n5457 when i made the first one, so i used a 2sk30 with twisted pins. Other than that, they are identical. And the one with the 2sk30 sounds a lot better. The 2n5457 one distorts easily, and has a trebly kinda noise to it. What purpose does the transistor serve in the circuit? Could it have this big impact, or have i done something wrong on the 2n5457 one?

    ReplyDelete
  14. Replies
    1. Hi Dedalo! Why ? Can u explain please !! Thanks

      Delete
  15. https://atomiumamps.tumblr.com/post/158975466951/speaking-of-compressors-here-are-my-fixes-for-the#notes

    ReplyDelete
  16. Speaking of compressors, here are my fixes for the Rothwell Love Squeeze circuit. It uses a JFET instead of an LDR in the feedback loop of an opamp. With no signal applied, the FET’s resistance is about 300 ohms and the stage’s gain is anywhere from unity to 10x, depending on the sustain control setting. When signal hits it, a P-P rectifier hits the JFET’s gate with a negative bias voltage in proportion to the input signal. The JFET’s resistance rises and reduces the gain of the first stage – compression. The advantage of the JFET is that its attack time is incredibly fast, limited only by the rectifier – half a wavelength of whatever fundamental frequency you’re hitting the front end with. The problem is that most people who build this circuit end up with distortion; it behaves like it has very little headroom.

    It has plenty of headroom, the problem is the way the sidechain blocks frequencies below 100Hz. It does this to avoid ‘pumping’ or overshoot on the compression envelope. But what you really get is phase shift in the sidechain at low frequencies, combined with lower drive and higher ripple on the P-P rectifier. So at a specific input level – right at the compression threshold – the circuit will snap in and out of compression very quickly, effectively acting like an LFO. It doesn’t do this at higher or lower signal levels, just at the threshold. You hear it as a blatty, sputtering decay on chords. It can be mitigated by increasing the release time (R11), but the only way to cure it is to let the sidechain run full-range. The changes above do that.

    (Note: you can get this behavior by simulating the circuit’s transient response in LTSpice, so it is definitely a design flaw and not a layout problem. In theory, certain selected JFETs might have curves that avoid the problem, so it’s not guaranteed to affect all builds… but why not fix it definitively?)

    There is a tradeoff, in that you will get some ‘pumping’ on big bass transients, but it is still far less noticeable than on more traditional compressors, because the attack time is so much faster. It seems possible to mitigate the overshoot by using a shelving filter in the sidechain amp instead of moving the highpass corner down. Maybe a -6dB filter below 100Hz. That might be a best-of-both-worlds solution, but I haven’t tried it.

    I replace R11 with a 25kB pot in series with a 15k resistor, which yields a much more traditional range of release times (roughly 100-300ms), with fewer intermodulation artifacts from rectifier ripple modulating the compression.

    Once this is done, there’s no reason to keep LEDs in the feedback loop, since only the absolute hottest pickups will distort the opamp, and only at max compression and for the first positive half-wave. It’s virtually inaudible.

    The other thing is that C12 should be no larger than 4.7nF, which attenuates treble above about 7.5kHz. The stock Rothwell uses 15nF (supposedly), which would explain why it has a reputation for being ‘dark’ sounding.

    ReplyDelete
  17. This comment has been removed by the author.

    ReplyDelete
  18. https://atomiumamps.tumblr.com/post/158975466951/speaking-of-compressors-here-are-my-fixes-for-the#notes
    IT REALLY HELPED A LOT. NOW IT SOUNDS RIGHT

    ReplyDelete
  19. don't work for me, just volume pot. can anybody help me?

    ReplyDelete
  20. I made this with few subsitutions


    I subsituted 22ohms with 18 ohms


    1n5817 with 1n5819



    I hear lot of poping while.im.playing idk how to decrease it.. any suggestions?

    ReplyDelete