Pages

▼

Friday, June 26, 2015

Creepy Fingers FuzzBud

Here's a great sounding one-knob fuzz from Creepy Fingers Effects for your FuzzFriday. It's based on the fuzz section of the Colorsound Fuzz-Wah and follows the basic structure of the Fuzz Face, just with a fixed resistor in place of the fuzz control. Shouldn't be hard at all to fit in a 1590a enclosure.



at

31 comments:

  1. UnknownOctober 6, 2015 at 11:48 PM

    Just verified! Awesome sounding little fuzz and super loud with the two 2N2222's! Thanks man

    ReplyDelete
  2. dtgehringOctober 7, 2015 at 9:17 AM

    Cool! Thanks for verifying, Charlie.

    ReplyDelete
  3. UnknownOctober 9, 2015 at 7:38 PM

    No prob! One question though. Do these transistors have to be matched?

    ReplyDelete
    Replies
    1. dtgehringOctober 10, 2015 at 11:23 AM

      It's a fuzz face derivative, so I'd start with a higher hfe on Q2 then experiment a bit.

      Delete
  4. constantineaudioDecember 11, 2015 at 12:37 PM

    Very loud fx, thanks https://www.youtube.com/watch?v=KTqQyF_t45A

    ReplyDelete
  5. UnknownJanuary 7, 2016 at 2:24 PM

    I builded this pedal and works fine, thank for effectslayouts.blogspot.com.br!!!

    ReplyDelete
  6. fredJanuary 14, 2016 at 3:22 AM

    2N2222A is good?

    ReplyDelete
  7. Michael GalanAugust 28, 2016 at 9:45 PM


    Built this but with 50k pot even at very little it is very very loud. So i cant get much range. if i turn it all the way it has no output but touch the pot even a little and it roars is there a way to control this to get some range that i can use.

    ReplyDelete
    Replies
    1. Effects LayoutsAugust 28, 2016 at 9:49 PM

      Did you try any different pots? Increasing the value should give it better range. Try 100k or 500k

      Delete
    2. Michael GalanDecember 9, 2019 at 10:57 PM

      using a bigger value pot seems to have no effect at all. correct me if im wrong but would using a smaller value pot allow more signal to be shunted to ground that lowering the overall output?

      Delete
  8. pakkee66April 17, 2017 at 1:37 PM

    Built it, awesome low end strong drive, like it very much,
    thanks for the layout..here share my board: http://i1244.photobucket.com/albums/gg569/pakkee66/DIY%20PEDAL/FuzzBud_zpswliul8w6.jpg

    ReplyDelete
  9. carlosrpdsjApril 20, 2017 at 4:12 PM

    schematic?

    ReplyDelete
  10. Urshurak776April 20, 2017 at 8:41 PM

    So use a B50K pot? I think the poster above had a bad one.

    ReplyDelete
    Replies
    1. Effects LayoutsApril 20, 2017 at 11:39 PM

      Use a 50k and if you don't like it try 100k or higher. YMMV

      Delete
    2. Urshurak776April 21, 2017 at 12:22 AM

      Thanks. I bought a 100k also. I have some 250k pots from my telecaster project. I'll try them out.

      Delete
  11. Sidahmed BkhJanuary 29, 2018 at 4:40 PM

    This comment has been removed by the author.

    ReplyDelete
  12. iNsTaNt oMarch 14, 2018 at 12:59 AM

    Is there a recommended parts list out there for a burgeoning diy pedal builder? Maybe even some recommended components for this pedal? Thank you!

    With L-U-V,

    O

    ReplyDelete
  13. UnknownAugust 1, 2018 at 9:58 AM

    where i can buy?

    ReplyDelete
  14. Max PietriniMarch 29, 2019 at 1:48 PM

    Verified Sound Amazing.

    ReplyDelete
  15. Michael GalanDecember 9, 2019 at 1:42 AM

    its says fix resistor in place of a pot for fuzz control. which resistor is that so i can experiment with pots

    ReplyDelete
    Replies
    1. Effects LayoutsDecember 9, 2019 at 12:59 PM

      The 1k resistor off the emitter of Q2. Though you'll probably want to remove the 10uF cap that's in parallel with the 1k resistor and run it between lugs 1 and 2 of a fuzz pot (negative lead going to lug 1 of the pot).

      Delete
  16. Secret SquirellJuly 31, 2020 at 5:15 PM

    I have verified this pedal as working..I used a B-250k pot . I made 2 of them first one with vintage can style transistors and second with modern plastic ones. I think the old can style sound better. what is the difference if any? am i wrong? also the only other difference would be a 1.2m resistor instead of 1m i was out? would that make the sound "thinner" it seems lacking in some way compared to the other one with can caps? thanks for any response. peace

    ReplyDelete
    Replies
    1. Effects LayoutsJuly 31, 2020 at 5:33 PM

      The 1M resistor is just the pulldown resistor so your footswitch doesn't pop, so using a large resistor isn't hurting anything. What's you're likely experiencing is the tolerance in caps. Most film caps have a 5-10% tolerance and ceramics around 10% or higher, meaning that the value will be with that percentage range. So between your two builds some of the caps may have been on the lower end of that range and others on the higher end. That'd be my guess anyway

      Delete
    2. Secret SquirellJuly 31, 2020 at 6:29 PM

      thanks man! hey do you think i am off about the transistors? thanks

      Delete
    3. Effects LayoutsAugust 2, 2020 at 12:07 PM

      I would expect some variance between metal can and plastic packages, but again, nothing too out of the ordinary. All BJTs regardless of package have an acceptable range of hFE that will vary from transistor to transistor. All that to say, the transistors will play a role in the difference between the two, but I would think the capacitors play a larger role.

      Delete
    4. Secret SquirellSeptember 3, 2020 at 4:21 PM

      I changed pot to A-10k it seems to work better...not so slamming loud right out the gate..and not as much noise. thanks for the help

      Delete
  17. Zaraki1337April 6, 2021 at 1:03 AM

    How can i add tone control i this?

    ReplyDelete
  18. E5July 2, 2021 at 6:30 AM

    Working perfectly with 100K pot here. Thank you effectslayouts.

    ReplyDelete