This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Wednesday, April 15, 2015

Zvex Wooly Mammoth

Looking for a Wooly Mammoth but don't want a sideways 1590b on your pedalboard? Here's the Zvex bass fuzz laid out for board-mounted right angle PCB pots.




22 comments:

  1. Can anyone explain routing to led, jacks and switches? This is my first pcb build and I'm having trouble

    ReplyDelete
    Replies
    1. There are a couple ways, but here's a good starting point:

      http://www.beavisaudio.com/techpages/StompboxWiring/StompboxWiring.gif

      Also check out the Tagboard Effects blog post on the subject.

      http://tagboardeffects.blogspot.com/2012/02/offboard-wiring.html

      As always, Google is your friend.

      Delete
  2. Can I use 1k pot and 220uf cap for the pinch setting?

    ReplyDelete
    Replies
    1. Cap might be ok, but I wouldn't use a 1k pot for Pinch. It's supposed to be 500k. Using a 1k would basically act as a switch.

      Delete
  3. What if i use a 10k pot for wool and a 1M pot for pinch? I've only these at home and i'm too lazy to buy new ones

    ReplyDelete
    Replies
    1. You can try it. You can also try soldering in some resistors in parallel to lower the pot values. A 1M resistor from lug 1 to 3 on a 1M pot makes it 500k. For the 10k pot try something around 2.5k

      Delete
  4. hello, comparing to other layouts, i see with put a diode (normal) and 1M resistence, and a third 100uF cap. Did you just followed a different schematic or was it a mod you decided to include?
    Thanks

    ReplyDelete
    Replies
    1. The 1M resistor is a pulldown resistor so a 3PDT footswitch won't pop and the diode and 100µ cap are for polarity protection and power filtering.

      Delete
    2. Thanks. Witchs pots will cause problems if I use log instead of linear?
      Thank you

      Delete
  5. Does anyone has any experience playing this with bass?
    I use this with bass, it gives me lots of sustain, but the attack has an envelope to it that I can't dial out. Maybe by lowering the gain in the pedal? (I already have pinch and wool turned all the way down).

    Thanks

    ReplyDelete
  6. Hi, should the pots be mounted from the solder side of the board? I'm new to this and unsure.

    ReplyDelete
  7. Built two of these sans pinch control. For bass I have 220nf filter caps, bc549 in Q1 and 2N3904 in Q2. This gave me THE fuzz tone I've been searching for to complement my jazz bass. A guitar player friend wanted one too. For that I used 100nf filter caps, 2N3904 in Q1 and BC549 in Q2. This produced a very subtle triangle wave oscillation with the fuzz tone in a cool, desirable way. I wish I didn't hard solder the bass version when I figured out the guitar version. Hope this helps someone.

    ReplyDelete
  8. Please someone make the woollymammoth7 layout, how can i build it?

    ReplyDelete
    Replies
    1. You can add a Rog tonemender to this layout and remove the mammoth’s tone control!

      Delete
  9. Would I have any problem if the 220nf and 10nf capacitors I put them in polypropylene? Thank you.

    ReplyDelete
  10. Hi. I built this pedal, it works fine but it has way too much low end for my guitar sound. How can I fix it?

    ReplyDelete