Pages

▼

Wednesday, January 11, 2017

Run of Groove Tonemender

Got a request for this one. It's a nice boost with a 3-band EQ. Pots are board mounted and it will fit in a 1590B sideways (ala Zvex pedals) with the circuit board vertical. From the Run Off Groove article:

 The Tonemender is a very flexible, yet simple clean boost with a 3-knob tonestack that allows the user to re-create the classic Fender, Marshall and Vox responses.
We suggest using a TLC2272 for the dual op-amp. The TLC2272 is rated for low-noise and rail-to-rail output, which will offer the highest possible clean boost and dynamic range. The NE5532 is another good choice, but a TL072 can also be used with decent results.
The Mid Shift switch (SW1 on the schematic) selects the center frequency of the midrange dip in the response. The center frequency is moved from around 700Hz (Marshall/Vox) down to 400Hz (Fender) in the HI and LO settings, respectively.
For Fender-style curves, the Mid Shift is placed in the LO setting (closed). To replicate Marshall-style curves, switch the Mid Shift to the HI position (open). Set the Mid control between 12:00 and 5:00 for traditional Marshall settings, with lower settings providing additional flexibility. For a Vox-style response, keep the Mid Shift in the HI setting and set the Mids control fixed at 10:00 and move the Bass between 7:00 and 12:00.
A "flat" equalizer position is set with the Bass and Treble both at minimum, and the Mid control at its midpoint. When Bass and Treble are fully cut, the Mid knob acts as an additional Level control, which is a familiar characteristic of the Fender tonestack.




at

29 comments:

  1. UnknownMay 10, 2017 at 1:22 PM

    Its verivied mate?

    ReplyDelete
  2. UnknownJanuary 13, 2018 at 1:13 AM

    I build it up, however its very noisy, i didn't put it in the case as i dont want to drill a box if its malfunctioning.

    ReplyDelete
  3. UnknownMarch 4, 2018 at 1:17 PM

    I built this, it works well but it's very noisy.
    is there anything that needs to be grounded and is not marked in the layout?

    ReplyDelete
  4. TomgunApril 18, 2018 at 10:22 PM

    Have you put it into enclosure?
    Mirosol from tagboardeffect said: "There's quite a lot of gain coming from the circuit, so some squeels and noise from the unboxed circuits are expected."

    ReplyDelete
  5. Charvel502April 18, 2018 at 10:42 PM

    I had noise issues with my build as well when testing, once boxed they were gone and it works like a charm, been on my pedal board ever since.

    ReplyDelete
    Replies
    1. TomgunApril 19, 2018 at 7:48 AM

      Where you put the tonemender?
      - after dirt pedal? so it act like preamp pushed by Dirt pedal, or
      - before dirt pedal? Act as base tone and push into dirts.

      Delete
    2. Charvel502April 20, 2018 at 12:49 AM

      I use mine at the end of the effects chain and use it as an overall adjustment to the sound, but I'm only using 2 other pedals before it at a time, may be different for your setup. I found it best after the dirt pedal when first playing with it

      Delete
  6. Charvel502August 23, 2018 at 12:51 AM

    Is there a way to add a "presence" pot?

    ReplyDelete
  7. The AplikatorSeptember 16, 2018 at 8:43 PM

    should this work well with bass?

    ReplyDelete
  8. jordaoAlvesJanuary 14, 2019 at 10:07 PM


    Can I turn it on "amplifier return"? would be too low? does it work with 18v?

    ReplyDelete
    Replies
    1. Effects LayoutsJanuary 21, 2019 at 9:26 AM

      It should work on 18v, assuming you've used appropriately rated caps. And are you asking if it can be used as a preamp?

      Delete
  9. MetalheadMarch 3, 2019 at 10:49 PM

    It's noisy

    ReplyDelete
    Replies
    1. sinaiAugust 7, 2019 at 12:52 AM

      Box it in metal enclosure, its very silent after box installation, remember keep wires as small as possible.

      Delete
    2. noneAugust 11, 2019 at 5:31 PM

      Shielded input and output cables also help

      Delete
  10. NatoApril 30, 2019 at 3:50 PM

    This comment has been removed by the author.

    ReplyDelete
  11. Brutha D (ave).June 23, 2020 at 2:41 PM

    I made last night, but swapped out the tone stack for the one in the link. I didn't use the mid shift switch, so had to use two jumpers.

    https://www.freestompboxes.org/viewtopic.php?f=13&t=28961

    ReplyDelete
  12. synthargentinaSeptember 21, 2020 at 12:20 AM

    for that noise problem, could try to do this, the first stage of the opamp most be that have the pot volume, and the second opamp stage just used as buffer (like the first one in schdmatic) you just have to make some tricks in this layout, but really works like a charm

    ReplyDelete
  13. Red Hood RocksApril 28, 2021 at 7:52 PM

    The Level Pot, It is normal that when you lower it everything continues to sound, shouldn't it be like that?

    ReplyDelete
  14. Bruno VianaMay 20, 2021 at 4:50 PM

    Would it be possible to make the tonemender .diy file available?

    ReplyDelete
  15. DIGISOUNDSeptember 22, 2021 at 7:45 PM

    Hola, las medidas de la placa estan disponibles?

    ReplyDelete
  16. Ismail cNovember 11, 2021 at 2:43 PM

    I have serious noise problem with this, build it three timesbut when I get my hand close the treble pot makes loud noise, tried grounded all pots, put it in a grounded box, used shilded cables but nothing work,

    ReplyDelete
    Replies
    1. Ismail cNovember 11, 2021 at 2:44 PM

      Also changed pots but makes no difference

      Delete
    2. RobNovember 25, 2021 at 5:55 PM

      Try using a bigger output cap than the 220uf like a 470uf or use a high voltage 220uf cap like 50v plus.

      Delete
  17. bigbizkitAugust 17, 2022 at 10:24 AM

    When i put the treble.pot to zero everything is quiet.. any probkem?

    ReplyDelete