Pages

▼

Friday, March 18, 2016

Cornish Buffer

Got a request for the Pete Cornish Buffer in dual form like the one I did with the Klon Buffer. So here's both a single and a dual Cornish Buffer. The original uses a 1N5401 for polarity protection, but a 4001 or similar will work too. And you can probably get away with a small value on the power filter cap (220ยต).

at

20 comments:

  1. UnknownMarch 21, 2016 at 10:26 AM

    I am really excited to see this buffer. I was looking at this and was wondering how you recommend wiring? I was looking at the layout at http://3.bp.blogspot.com/-DSD3O8O8mx8/U5rGpCi5KgI/AAAAAAAAHzQ/u5fPoB7Dgwo/s1600/Cornish+G2+bypass+buffer+wiring.png
    and was wondering how you would wire the in and out buffer option. Also I was wondering if you were thinking of layouts for the Cornish G2 and SS2 as well? I appreciate all that you do. I love this site.

    ReplyDelete
    Replies
    1. Effects LayoutsMarch 28, 2016 at 9:30 AM

      Thanks! You'd wire it the same way as Mark's drawing. Input jack would go to the In pad of the buffer, Out pad to the switch. The same lug of the switch the buffer Out is wired to would connect to the In pad of whatever effect you're using and the Out pad of that effect would connect to the switch where Mark's drawing says "Vol 2". Hope that helps!

      Delete
  2. shimanekoOctober 23, 2016 at 9:16 AM

    The single one is verified.I would install it into my guitar!

    ReplyDelete
    Replies
    1. JSTNMarch 22, 2018 at 11:25 AM

      I thought about doing this.
      as I've connected it to my guitar strap connected by a 7" cable and it definitely added more fidelity than placing it 20' down the line.
      honestly this buffer does very well being 'overused' every single one of Petes standalone pedals has this on this I/O. I always make sure to have this at the beginning of my chain and at the end on the way to the amp.

      Delete
  3. albDecember 12, 2016 at 3:42 PM

    I have a problem with this pedal. I've made 3, 1 in protoboard, 1pcb and 1 in a breadboard. Every pedals have a volume drop. I don't know if this volume drop is normal. I use a bc549b, and the same values of the template.


    Who could help me?

    ReplyDelete
    Replies
    1. Effects LayoutsDecember 12, 2016 at 3:44 PM

      Try using a BC549C. The B version is much lower gain.

      Delete
    2. albDecember 12, 2016 at 3:51 PM

      Also I've tried with bc547 with more hfe and 3904 with the same result.
      Don't you notice volume drop in your Cornish Buffer?

      Delete
  4. diegoolAugust 14, 2017 at 3:20 AM

    THANK YOU
    it worked very well without volume drop

    ReplyDelete
  5. JSTNJanuary 1, 2018 at 11:35 PM

    I'm wondering about the 1N5401 diode.
    I've done this build, and it seems pretty accurate.
    I'm not by any means an electrical engineer. I've just done couple DIY's
    BUT the 1N5401 it doesn't seem to be in the pictures and it's not in my OC-1 that I have opened or my TES that I purchased that was open.

    ReplyDelete
    Replies
    1. Effects LayoutsJanuary 2, 2018 at 9:14 AM

      It's for polarity protection and was probably on the main board of production models. I included it on this board as people have used it as a stand alone effect.

      Delete
    2. JSTNMarch 22, 2018 at 11:22 AM

      thanks. I just saw this.
      I understand this now...
      you are the first person to respond to this and confirm what I assumed.

      Delete
  6. divanorossoApril 5, 2018 at 3:02 PM

    Sorry, i have a question.
    I do not remember where but I read that the 50k resistance is fine so if the buffer is used alone. Instead, if the buffer is in front of an effect, the 50k does not go to ground but connected in series between the 150R and the output. It's right?

    ReplyDelete
    Replies
    1. Effects LayoutsSeptember 10, 2018 at 9:55 AM

      It's quite possible. I would probably just remove the 50k resistor all together if it were me. YMMV

      Delete
  7. gennaroSeptember 8, 2018 at 5:05 AM

    hello I have the same problem of alb ie a drop in volume, I followed the pattern as it is in the picture. How can I solve?

    ReplyDelete
    Replies
    1. Effects LayoutsSeptember 10, 2018 at 9:55 AM

      I would try just removing that 50k resistor if you're getting low output.

      Delete
  8. SergioOctober 15, 2018 at 5:35 AM

    can i replace non standard R values with standard values? like... 7.5k by 8k,20k by 22k,50k by 47k, 200k by 220k?

    ReplyDelete
  9. pearl bluesNovember 18, 2018 at 11:43 AM

    I built this and it definitely is a nice buffer but I've found that it does cause some noise problems with other pedals in my chain, for example I now get a pulsing noise from my univibe even when it's switched off, but if I disconnect the buffer that noise goes away. Plus, it makes my fuzz pedals more noisy. It is lovely with just a clean sound though, and also really enhances my tubescreamer, so I'll probable keep it for certain situations. Thanks for the layouts on this page... I've made three from this site so far and they've all worked first time! Peace :)

    ReplyDelete
  10. pearl bluesNovember 18, 2018 at 1:14 PM

    *update* It turns out that I've uncovered a few gremlins in my pedalboard, so the noise issues weren't anything to do with the Cornish buffer. Apologies for any confusion ;)

    ReplyDelete
  11. pearl bluesNovember 25, 2018 at 1:44 PM

    *update 2* The Cornish buffer has been on my pedal board for about a week and it's definitely a keeper now! In my setup it works best as the second in my pedal chain after my compressor...

    ReplyDelete