Pages

▼

Monday, April 20, 2015

Ibanez TS9 Tube Screamer

The TS808 layout I post a while back has always bugged me. It's a real tight squeeze in a 1590B and I wanted a Tube Screamer layout with onboard pots. Well, I finally drew one up and I like this one. It's laid out for the TS9, but all it takes is 2 resistor swaps to go to TS808 specs (see the layout for info there). For board mounted pots, as per usual, right angle PCB pots can be mounted from the solder side of the board.


at

75 comments:

  1. GuilhermeJuly 22, 2015 at 9:45 PM

    Probably I'm making a dumb mistake, but I can't verify this. All I get is a crazy farting tone, sounds like ass and I'll take some days off from debuging it, because I'm pissed hehe

    ReplyDelete
    Replies
    1. dtgehringAugust 24, 2015 at 9:22 AM

      I went back and double checked it. I had forgotten the 10k resistor from 9v to Bias. *facepalm It's fixed now.

      Delete
    2. GuilhermeSeptember 12, 2015 at 5:05 PM

      hahahaha, I'm not that bad at building pedals, then. I just need to check it with the schematics more often. I'm about to verify it!

      Delete
    3. DikdikSeptember 16, 2024 at 5:56 PM

      Sama! Adakah gambar untuk jalur yang salah?

      Delete
  2. UnknownAugust 23, 2015 at 11:01 PM

    https://www.youtube.com/watch?v=omKi0luhjAA

    ReplyDelete
    Replies
    1. dtgehringAugust 24, 2015 at 9:24 AM

      Your video says you built it from the Tonepad layout. Why are you posting it here?

      Delete
    2. RonieNovember 5, 2019 at 9:34 AM

      Candra, lu kebanyakan gaya tong

      Delete
  3. GuilhermeSeptember 12, 2015 at 6:04 PM

    Yep, that made it, you can tag it!

    ReplyDelete
  4. TRAINERSeptember 14, 2015 at 5:43 PM

    Thanks man!
    I tested the circuit today and it worked.It's a very good tone!

    ReplyDelete
  5. dtgehringSeptember 14, 2015 at 9:49 PM

    Great! Thanks guys.

    ReplyDelete
  6. UnknownOctober 28, 2015 at 8:21 PM

    Hello there!
    I think there is a tiny mistake in the ready to transfer image. One of the holes of the 51pf cap is missing isn't it?
    Great site by da way. I have to send photos some day! :)

    ReplyDelete
  7. MitchSchaftNovember 13, 2015 at 1:26 AM

    Can I use this to make a clay jones OD replica? or are the LED pads not there?

    ReplyDelete
    Replies
    1. dtgehringNovember 13, 2015 at 9:14 AM

      The Clay Jones OD uses 3mm LEDs instead of the typical 1N4148s, so the layout isn't set up for LEDs, but it won't be a problem to squeeze them in there. Otherwise the only difference between the TS9/808 and the Clay Jones is just a handful of component values. The "topography" of the circuit is the same, so you shouldn't have any issues.

      Delete
    2. MitchSchaftNovember 14, 2015 at 2:15 AM

      Thanks, man. I'll give it a shot.

      Delete
    3. MitchSchaftNovember 14, 2015 at 6:58 AM

      What size drill bit do you use?

      Delete
    4. dtgehringNovember 14, 2015 at 9:13 AM

      You'll need a couple different sizes. I use one of these stepped bits. Works much better than typical twist bits. Best to measure your own components before drilling.

      Delete
  8. UnknownJanuary 2, 2016 at 6:13 PM

    Hi! I just came across a topic on freestompboxes forum and converting the TS9 to 808 takes more than 2 resistors as I understand. I guess they are refering to the Tonepad's layout but I wanted to make sure as I'd like to use your layout because I'm such a loyal DIYer :) You can check it out here: http://www.freestompboxes.org/viewtopic.php?f=1&t=22777
    They also mention a capacitor change and the direction of diodes. I'm not sure it will make a difference but I wanted to take your opinion.

    ReplyDelete
    Replies
    1. Effects LayoutsJanuary 4, 2016 at 11:53 AM

      Yeah, that's referencing the TonePad board, which you can build the TS-808, TS-9, and Boss SD-1 on. I believe the cap in question isn't even populated for the Tube Screamers, and diode direction doesn't matter. That would only matter if you're using asymmetrical clipping, which is what the SD-1 uses (though it's a common mod to the TS circuit, by my layout doesn't really allow for it). So, long story short, the only difference between the 808 and the 9 are those 2 resistors. Good luck with your build and thanks for the loyalty! :D

      Delete
    2. UnknownJanuary 4, 2016 at 4:37 PM

      Thanks a lot! That's a relief :)

      Delete
  9. MayMarch 23, 2016 at 12:11 PM

    I don't know what i'm doing wrong. mine dont works, at beginning, i realized that the 10uf capacitor was inverted.

    ReplyDelete
  10. AnonymousAugust 8, 2016 at 10:12 AM

    What kind of switch I need to change between ts808 and ts9? I mean, use the switch to change the resistors of the two models...
    Thanks!

    ReplyDelete
    Replies
    1. Effects LayoutsAugust 8, 2016 at 1:07 PM

      You can use a DPDT on/on and wire it like this:

      https://postimg.org/image/r20opo9ff/

      Delete
    2. UnknownApril 12, 2018 at 9:15 PM


      Can you make the upload of image again?

      Sorry my english, i'm from Brazil.

      Delete
    3. Effects LayoutsApril 13, 2018 at 12:02 PM

      http://members.optushome.com.au/bluespherecreations/forum/resistorswitching.gif

      Delete
    4. Dalvare.s01613October 23, 2018 at 1:47 PM

      Can u upload again?

      Delete
    5. Effects LayoutsOctober 23, 2018 at 3:17 PM

      https://i.postimg.cc/bwyw5QRH/TS808-9-switching.png

      Delete
  11. UnknownJanuary 24, 2017 at 7:48 PM

    Just built one of these. Video of me playing around on it. Sorry for not explaining which settings I'm using, I forgot what I was doing :)
    https://youtu.be/yeu3Doze9FI

    Or just skip to the clip with backing track. https://youtu.be/yeu3Doze9FI?t=161

    ReplyDelete
  12. UnknownMay 4, 2017 at 9:41 AM

    i have buit it great layout as always
    my question is this
    is there a drilling template available?
    best regards from greece

    ReplyDelete
  13. naponosSeptember 20, 2017 at 11:12 AM

    Hi... the volume level does not increase enough, it seems that the clean sound is higher than the distorted, is it possible? What can you do to overcome this?

    ReplyDelete
    Replies
    1. Effects LayoutsSeptember 20, 2017 at 11:40 AM

      Troubleshoot.

      http://www.diystompboxes.com/pedals/debug.html

      Delete
  14. UnknownNovember 19, 2017 at 1:41 PM

    Hi, can you tell me, where I can find the Schematic to this board? Thx

    ReplyDelete
  15. UnknownJanuary 31, 2018 at 5:07 AM

    I cant find any 1uf mylar capacitor.is it possible to use 1uf elco caps for this.?not really sure how to put them in this board.i mean the polarity orientation.
    Thank you for the great upload.

    ReplyDelete
    Replies
    1. Effects LayoutsJanuary 31, 2018 at 2:41 PM

      The caps don't have to be mylar, but they do need to be non-polarized.

      Delete
    2. UnknownFebruary 1, 2018 at 3:55 AM

      Thanks for the reply man..

      Delete
  16. UnknownApril 12, 2018 at 10:28 PM

    Sorry for the question, but how do I turn on the switch switch?

    ReplyDelete
  17. UnknownApril 15, 2018 at 4:32 PM

    Just one more thing...
    In case I want to use a switch that alternates between asymmetric and symmetric diodes. Could you tell me how to make this connection?

    ReplyDelete
    Replies
    1. Effects LayoutsApril 15, 2018 at 4:55 PM

      Wire diodes to a DPDT like in this layouts (just replace the two LEDs with an asymmetric diode array) and wire the 2 middle lugs of the switch to one of the places where diodes are on the board (and don't populate the diodes on the board if you're putting them on a switch).

      Delete
    2. Effects LayoutsApril 15, 2018 at 4:55 PM

      http://4.bp.blogspot.com/-_SfO_0LxRdA/UyRV5uYYWeI/AAAAAAAAGSY/dbNm95s5ScQ/s1600/Ibanez+TS808+compact+with+clipping+switch+Rev2.png

      Delete
    3. UnknownApril 16, 2018 at 12:13 PM

      Thank you so much!
      I can use different diodes?

      Delete
    4. Effects LayoutsApril 16, 2018 at 4:41 PM

      Of course! Red LEDs are good, 4148s, etc.

      Delete
  18. Dalvare.s01613November 21, 2018 at 2:22 PM

    can i use a b100k for tone?

    ReplyDelete
  19. felanggaMarch 21, 2019 at 1:21 AM

    The IC is using TL072 or JRC4558 ?
    I read that they are interchangeable, but how about the sound?

    ReplyDelete
    Replies
    1. Effects LayoutsMarch 21, 2019 at 9:19 AM

      Yes, you can use just about any dual opamp. But the sound may be slightly different with each. This is why I generally suggest to use a socket so you can try out different chips.

      Delete
  20. TanzkiztraMay 22, 2019 at 7:21 PM

    So what value can i replace with 1uf nonpolarized.....i cannot find it in any local stores here..

    ReplyDelete
    Replies
    1. Effects LayoutsMay 23, 2019 at 9:22 AM

      Anything higher value. 680n, 470n, etc. Even 100n would work.

      Delete
    2. ZoedroonJune 15, 2020 at 7:23 PM

      Mugo² keno lan suarane penak. Yen ora tak keplaki sirahmu.

      Delete
    3. Zaraki1337March 27, 2021 at 11:38 PM

      Wud it change the sound if i usee 100nf instead of 1uf?

      Delete
  21. RobertoAugust 1, 2019 at 7:16 AM

    Bom dia!!! Fiz um ts9 e percebi que o potenciometro de volume está com pouco volume! Comparado ao ts9 original,enquanto o o pot do original está no meio, o pot desse está bem mais aumentado pra ficar na mesma altura!! O que pode ser feito pra dar mais volume nele?

    ReplyDelete
  22. EmilianoSeptember 2, 2019 at 11:46 AM

    May I use 33nF instead of 27nF? Or will it lead to worse sound quality?

    ReplyDelete
  23. StefanoOctober 15, 2019 at 5:10 AM

    Ho guys!
    Help!
    the circuit works well for a few minutes then starts making noise until it no longer works.
    Some idea?!?
    Thanks a lot,
    Stefano!

    ReplyDelete
    Replies
    1. StefanoOctober 15, 2019 at 5:15 AM

      I have solder 5819 instead 5817, 47pf capacitor instead 51pf and a 2m resistor instead 2.2 becose i haven't.

      Delete
    2. StefanoOctober 15, 2019 at 5:44 AM

      I have test every component before soldering. I try tl072 and the result is the same.
      Thanks for every help!
      (sorry for my English, i'm Italian)
      Stefano.

      ReplyDelete

      Delete
    3. StefanoOctober 19, 2019 at 11:26 AM

      maybe the 47pf capacitor? or the resistor?

      Delete
  24. StefanoOctober 15, 2019 at 5:43 AM

    This comment has been removed by the author.

    ReplyDelete
  25. RonieNovember 19, 2019 at 3:52 AM

    hi .. i'm having a problem the sound produced is only clean sound .. even when the drive knob is fully rotated. any advice? thank you

    ReplyDelete
  26. TesLateralusSeptember 23, 2020 at 10:07 PM

    Hi, i can't find the diode where i live, but instead i have the 1n914b, can i use it?
    And also, i can't find the 51pF cap, so can i use a 47pF?

    ReplyDelete
  27. UnknownOctober 22, 2020 at 5:52 PM

    What size pots do you use for onboard? 16mm don’t match the template no matter how I place them, either side

    ReplyDelete
  28. UnknownDecember 9, 2020 at 4:25 PM

    I'm finding the transfer image is a bit pixelated, and the size isn't quite right. Can you post this as a PDF or other better quality file? I built your 1590B Big Muff project, and the image quality was much better on that one. TIA!

    ReplyDelete
    Replies
    1. UnknownDecember 9, 2020 at 4:28 PM

      Nevermind - just saw the note linking to the transfer image library - problem solved!

      Delete
  29. Zaraki1337February 8, 2021 at 5:15 AM

    Can i use lm358 instead of 4558??

    ReplyDelete
  30. Zaraki1337February 17, 2021 at 1:30 AM

    Can i use 4007 instead of 5817

    ReplyDelete
  31. Zaraki1337February 17, 2021 at 3:30 AM

    And theres is a noise.. circuit works but theres is loud noise.. when i checked it 249hz noise.. anumy suggestion?

    ReplyDelete
  32. Zaraki1337February 17, 2021 at 7:57 AM

    Anyway i can reduce noise? I tried diffrent amp

    ReplyDelete
  33. UnknownJanuary 30, 2022 at 9:45 AM


    I made it but there is no sound, and if I touch the ground it will sound "Hiizzz" the same as touching the input and output... can anyone help me?? Please

    ReplyDelete
  34. UnknownMarch 6, 2022 at 11:51 AM

    HEllo.
    Is MYLAR caps fine with this pedal. Does mylar caps reduce the distrotion effect?

    ReplyDelete
  35. Cris PizzolatoNovember 14, 2022 at 7:09 PM

    how can i replace 5017?

    ReplyDelete