tag:blogger.com,1999:blog-5481402030233340127.post8287158997944372620..comments2024-03-28T01:15:58.057-04:00Comments on Perf and PCB Effects Layouts: Lovepedal Hi Voltdtgehringhttp://www.blogger.com/profile/09555201436004501222noreply@blogger.comBlogger12125tag:blogger.com,1999:blog-5481402030233340127.post-22964913278421546262018-03-05T14:54:23.379-05:002018-03-05T14:54:23.379-05:00You can use the 7660 in place of the 1044. And to ...You can use the 7660 in place of the 1044. And to my knowledge it hasn't been verified yet.Effects Layoutshttps://www.blogger.com/profile/11341183658959824998noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-28756849063399611282018-03-05T14:42:41.362-05:002018-03-05T14:42:41.362-05:00Can I use the ICL7660S in the location of the MAX1...Can I use the ICL7660S in the location of the MAX1044? Has this layout been successful?wainer.said@gmail.comhttps://www.blogger.com/profile/06287281265541984906noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-11401705652833729112017-04-11T11:24:48.182-04:002017-04-11T11:24:48.182-04:00I've fixed the layout. Thanks for figuring out...I've fixed the layout. Thanks for figuring out what was wrong, guys. Effects Layoutshttps://www.blogger.com/profile/11341183658959824998noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-68983932532517007062017-04-10T06:31:21.527-04:002017-04-10T06:31:21.527-04:00Hello, again!
After I added a wire between pin 3 ...Hello, again!<br /><br />After I added a wire between pin 3 of the mid pot and pin 2 of top TL072 (as John Kallas suggested above), the effect sounds very well, almost as in the videoclips. Anyway, I will test it these days at higher volumes :)<br /><br />Thank you very much all!raduandroidulhttps://www.blogger.com/profile/13178852141315792702noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-33438077796205221442017-04-08T02:25:02.766-04:002017-04-08T02:25:02.766-04:00Jesse, I am interrested to see the original schema...Jesse, I am interrested to see the original schematic, too...i will be grateful if you will send it to me at radu.androidul@gmail.com...thank you!raduandroidulhttps://www.blogger.com/profile/13178852141315792702noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-54031045991872910852017-04-07T13:44:05.310-04:002017-04-07T13:44:05.310-04:00judging by the schematic posted on FSB, pin 3 of t...judging by the schematic posted on FSB, pin 3 of the mids pot should connect to pin 2 of the top TL072. i corrected the charge pump on mine and then used a jumper to connect it and it works, but it doesn't sound quite like the original pedal to me.<br /><br />Jesse, i'd also like to see the original factory schematic. if you could email it to me at jrkallas@verizon.net i'd really appreciate itjohnkhttps://www.blogger.com/profile/00643996045674470081noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-88155688302070659302017-04-07T13:15:17.116-04:002017-04-07T13:15:17.116-04:00Feel free to email it to me
gehringcustomguitars@...Feel free to email it to me<br /><br />gehringcustomguitars@gmail.comEffects Layoutshttps://www.blogger.com/profile/11341183658959824998noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-88860350151666503752017-04-07T02:52:15.678-04:002017-04-07T02:52:15.678-04:00i would send the schematic to you however to check...i would send the schematic to you however to check against the layout you've made if you'd like so we can get this one verified :)Anonymoushttps://www.blogger.com/profile/17650462389842308339noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-57306927287716909782017-04-07T02:46:59.998-04:002017-04-07T02:46:59.998-04:00I have the original schematic that it was redrawn ...I have the original schematic that it was redrawn from, perhaps there was an error made when I had it redrawn to share by another member. The one I have is the factory schematic sent to me by Sean so I don't feel it's right to share without redrawing it Anonymoushttps://www.blogger.com/profile/17650462389842308339noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-13837988009563220342017-04-05T16:54:29.791-04:002017-04-05T16:54:29.791-04:00Thanks for the report. I'll correct the charge...Thanks for the report. I'll correct the charge pump on the layout.Effects Layoutshttps://www.blogger.com/profile/11341183658959824998noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-73796753708149855952017-04-05T16:53:29.244-04:002017-04-05T16:53:29.244-04:00Thank you very much for your wonderful layouts!
...Thank you very much for your wonderful layouts! <br /><br />I've just finished HiVolt, but it didn't work. I found that the problem comes from the power supply part, which is wrong on the FSB schematic. So, you must disconnect 1N4001 diode from the pin 7 of MAX1044 and connect it to pin 8 (as I saw in many others schematic). Because I am lazy, I cut the pin 7 from the IC and I soldered together pins 7 and 8 :)<br />Now it works, but not as in videos. It hasn't a tight sound. It has a muffled sound. Maybe are other errors in the schematic.<br /><br />Best regards!<br />raduandroidulhttps://www.blogger.com/profile/13178852141315792702noreply@blogger.comtag:blogger.com,1999:blog-5481402030233340127.post-1087835300856013082017-03-29T12:12:30.736-04:002017-03-29T12:12:30.736-04:00OMG!!
Awesome!OMG!!<br />Awesome!Berkicauhttps://www.blogger.com/profile/11496934027004271830noreply@blogger.com